9 Uncommon tips for installing inflatable spas

9 Uncommon tips for installing inflatable spas

Posted by

If you’re new to inflatable spas or haven’t used one in a while, you might have some questions regarding set-up and maintenance. The good news is… You may rest confident that the procedure will be simple and uncomplicated. Let’s take a closer look.

9 Uncommon tips for installing inflatable spas

An inflatable spa is intended to resemble a traditional spa or jacuzzi. On the interior and outside, inflatable spas are often made of PVC vinyl material.

Once inflated, just fill the tub with water and switch on the heater to raise the temperature. This heat is kept in the water to keep it warm for a comfortable bath. A pump that generates pulsing bubbles via jets can circulate the water.

Inflatable spas may contain a filtration system, depending on the type, to assist keep the water and jets clean and unclogged.

You don’t have to commit to having a permanent structure put on your deck, patio, balcony, or garden because inflatable spas are fully movable.

When you no longer wish to use it, such as during the winter or when you move, you can deflate it and put it up for convenient storage or transit.

To know more about inflatable spa visit https://havanaspas.com.au/

9 pointers for installing and maintaining an inflatable spa

To make the procedure easier, each kind of inflatable spa has slightly different set-up instructions. You should spend some time reading the owner’s manual that came with the spa. Typically, the handbook is chock-full of step-by-step setup instructions. Many manufacturers will connect you to an online video that will show you how to complete the setup fast and easily.

Here are nine helpful suggestions to keep in mind while getting started with your tub:

1. Select the ideal place.

When choosing a place for the spa, consider the ultimate measurements once the spa has been fully inflated and filled with water. Take measurements to guarantee that the spa will fit when completely completed.

2. Place the spa close to a power source.

Choose a spot for the inflatable spa that is close to a power supply. If at all possible, avoid using an extension cable. An extension cable is a possible safety hazard that, in some cases, can become a fire hazard. If there isn’t a power outlet nearby where you want to put your inflatable spa, have an electrician build one.

3. Take note of the terrain

The location where your inflatable spa will be put up should be flat and smooth. If you position the spa on uneven or sloping ground, the water level will be off and you will not feel comfortable sitting in the spa. Furthermore, the water will flow to one side of the spa, skewing it and putting stress on one side of the tub, perhaps damaging the inflatable liner.

Always inspect the area where you intend to install the spa to ensure that there are no sharp items or rough surfaces that might cause a hole in the vinyl surface of the spa. Although the spa’s skin is surprisingly resistant, the pressure from the water can cause a sharp instrument to penetrate the vinyl.

4. Consider the filled weight of the spa.

If you intend to place the spa on a deck or floor, ensure that it can support the weight of the water-filled tub. A fully loaded hot tub might easily weigh more than 900 kg.

5. Seek assistance with the setup procedure (if needed)

The setup of an inflatable spa is very simple. The work can be completed by one person, but if you have a loved one who is ready to assist, the assembling procedure will be much faster. You may choose to inflate the spa in an open area before transporting it to its permanent placement. Although the spa is lightweight, it is enormous and bulky, therefore transporting it with two persons is preferable.

6. Fill the tub with water.

Avoid overinflating the hot tub, since this can put strain on the seams and eventually cause them to fail. The sides should be solid but not stiff to the touch, with only a small give. If the sidewalls are overinflated, they will begin to deform as you fill the tub with water, causing the spa’s final shape to seem crooked.

7. Take cautious not to overload the spa.

Don’t overfill the hot tub. Bring the water only up to the fill line, which is visible on the inside surface of the spa. Remember that the water in the hot tub will increase while you sit in it. In addition, the water must have enough space to bubble without splashing over the spa’s edges. Most spa models have a fill line with a minimum and maximum fill line. It is normally ideal to fill the spa all the way to the bottom. Then, as needed, add extra water to meet the maximum fill line.

8. Use the proper chemicals.

You should use either chlorine or bromine with your chemical floater. Keeping the water sterilized keeps it safe to use and extends its life so you don’t have to replace it. A chemical test kit may be purchased to check the various chemical levels in the water to ensure that they are safe.

9. Consider maintenance carefully.

Once the pool has reached the correct temperature, you may add a sanitizer to the water to maintain it clean and free of germs, which may develop quickly in untreated hot water. Sanitizers are classified as either chlorine or bromine. Never use household bleach in your spa since it might harm the system or liner as well as burn your skin.

Your spa most likely comes with a floating chemical dispenser into which you may drop the chlorine or bromine tablet. Depending on the size of the spa, you can use two to six tablets. Allow the floater to freely float in the spa water. The pills will degrade in three to five days and will need to be replaced. Slow dissolve pills with a shelf life of one to two weeks can be purchased.

Ideally, you should replace the water in the tub every six weeks, especially if many people use it often. Even if the necessary chemicals are used, the water might become hazy or unclean if left untreated.

Final thoughts

With what we’ve discussed, you should know how to better care for inflatable spas